价格:未填起订:20
供应:484
发货:1天内
PPS2000 LEXIA-3接口适用于雪铁龙和标致！它兼容雪铁龙和标致汽车从1995年。它支持读取识别，读取故障码，清除故障码，自动扫描...
雪铁龙/标致诊断LEXIA-3 V47 PP2000V25 Diagbox V6.01软件支持标致307PPS2000 LEXIA-3接口适用于雪铁龙和标致！
但不适合雪铁龙C5。
对于您的标致雪铁龙C5，您可以选择FR704。语言包括：
英语，德语，法语，日语，俄语，西班牙语，葡萄牙语，瑞典语，土耳其，荷兰，波兰，意大利，匈牙利，希腊，捷克LEXIA-3产品说明：
不像其他通用汽车扫描工具，读取故障码，该软件执行几乎所有的功能。我们的诊断接口包含K线多路复用器，CAN-BUS接口和SAE J1850总线（包括PWM和VPW）。支持下列诊断功能：
- 1，读取识别
显示完整的识别控制单元，如部分号码，软件/硬件版本，制造商，等..- 2。读取故障代码
显示存储和待故障代码，完整的描述（如“铁路压力 - 压力过低”）。
程序支持报表打印或复制到剪贴板。- 3。清除故障码
此功能会清除所有存储的故障代码和其他诊断信息。- 4。自动扫描（整车扫描/测试）
检测所有的ECU（电子控制单元）安装在汽车和读取所有的诊断故障代码。- 5。测量值
程序显示实时数据，如发动机转速，电池电压，氧传感器，冷却液温度等。- 6。执行器测试
执行器测试激活特定的驱动器（如燃油泵的开启，锁定/解锁轮，锁定/解锁门，切断燃油等...）兼容的车辆：
它兼容与雪铁龙汽车，包括C1，C2，C3，C4，C6，C8，C-CROSSER，NEMO，BERLINGO，JUMPY等。但请注意，不能工作在C5车型。可以兼容大多数的标致汽车从1995年开始通过OBD-II连接器（位于方向盘附近）或通过制造商特定的连接器（2001年以前的）进行诊断。硬件和软件要求：
软件需要至少英特尔/奔腾III 400兆赫，128 MB RAM，50MB硬盘空间和USB 1.1端口（建议使用USB 2.0）和Microsoft Windows 98 SR2/2000/XP提供最新的服务包安装。
套餐包括：
1个主单元与扩展OBD2电缆
1个长度9针USB电缆
1个9针短USB电缆
1个OBD2电缆
1个16PIN剪辑电缆
1个指令安装和激活的DVD PP2000
经营LEXIA-3 PP2000提示：
1。运行XP系统上的软件
2。在安装前关闭防病毒系统
3。通过CD此产品更新，请不要在其官方网站上更新，否则可能会损坏设备PPS2000 Lexia-3 Interface works for both Citroen and Peugeot! It is compatible with most of Citroen and Peugeot cars from 1995. It support read identification, read fault codes, clear fault codes, auto-scan ...
Update to latest version: Lexia-3: V47, PP2000: V25
Lexia3 is multi-language optional and update via CD.
Lexia-3 Lexia3 v47 Citroen / Peugeot Diagnostic PP2000 V25 Diagbox V6.01 Software Support Peugeot 307
Buy lexia-3 pp2000 get Diagbox V6.01 Software freely It can work on Peugeot 307 well now
PPS2000 LEXIA-3 Interface works for both Citroen and Peugeot!
But not good for Citroen C5.
For your Peugeot Citroen C5, you can choose FR704. It will be a good choice.
Update: Via CD Language included:
English, German, French, Japanese, Russian, Spanish, Portuguese, Swedish, Turkish, Dutch, Polish, Italian, Hungarian, Greek, Czech
Lexia-3 Description:
Unlike other universal car scanner tools which only read fault codes, this software performs nearly ALL the functions like the original dealer diagnostic tool. Our diagnostic interface contains K-Line multiplexor, CAN-BUS interfaces and SAE J1850 bus (both PWM and VPW).
The following diagnostic functions are supported:
- 1.Read identification
Displays complete identification of control unit, eg part number, software / hardware version, manufacturer, etc ... - 2. Read fault codes
Displays all stored and pending fault codes with complete description (eg "Rail pressure - too low pressure").
Program supports report printing or copy to clipboard. - 3. Clear fault codes
This function clears all stored fault codes and other diagnostic information. - 4. Auto-scan (complete car scan / test)
Detects all ECUs (electronic control units) installed in car and reads all diagnostic fault codes. - Measured Values
Program displays live Data like Engine Speed, Battery voltage, Oxygen Sensor, Coolant Temperature, etc. Values ??can be displayed in graph, 9 values ??at once, or full listing (all measured values). Logging to file is also supported, which allows offline analysis. - 6. Actuator test
Actuator test activates particular actuator (eg turn on fuel pump, lock / unlock wheel, lock / unlock doors, cut off fuel, etc ...)
Compatible Vehicles:
It compatible with Citroen cars including, C1, C2, C3, C4, C6, C8, C-CROSSER, NEMO, BERLINGO, JUMPY, JUMPER, AX, SAXO, BX and so on. But please pay attention, according to our customer's experience , this item cannot works good at C5 models. It compatible with most Peugeot cars from 1995 Diagnostics is performed via OBD-II connector (which is located near steering wheel) or via manufacturer-specific connector (only older cars, pre-2001).
New vehicles are added to Lexia-3:
Peugeot Bipper
Peugeot Boxer III
Peugeot Boxer III minibus
Citroen Nemo
Citroen Jumper III
Citroen Jumper III minibus
Hardware and software requirements:
Software requires at least Intel Celeron / Pentium III 400 MHz, 128 MB RAM, 50MB free HDD space and USB 1.1 port (USB 2.0 recommended) and Microsoft Windows 98 SR2/2000/XP with the latest service pack installed. Package includes:
1pc x Main unit with extension OBD2 cable
1pc x Long 9pin to USB cable
1pc x Short 9pin to USB cable
1pc x OBD2 cable
1pc x 16pin to Clip Cable
1pc x Instruction for Installation and Activation DVD for PP2000
Tips on operating lexia-3 pp2000:
1. Run the software on XP system
2. Close the anti-virus system before your installation
3. This item update via CD, please do not update it on offical website; otherwise the device may be damaged
